Approx. Rs 143 Lakh / UnitGet Latest Price
Product Details:Minimum Order Quantity | 1 Unit |
Design Type | Standard |
Capacity | 100 |
Automatic Grade | Automatic |
Power Consumption | 220vAC 3.65Kw |
Special Features:Solvent recovery unit for photopolymer flexo plates
A. General description:
This is designed for recovery of flexographic photopolymer plate solvent washout chemical and any environmental green chemical with specialties of distilling and cooling can be connected with in-line processor and any plate washout machine directly. With cold air circulation and drain out of residue for high speed recovery. Super recovering rate in the shortest time, is an ideal and high efficient recovery unit for flexographer.
B. Technical information:
Recovery Volume: 80 Liter
Power Consume: 220v AC, 5.65Kw
Dia Thermic Oil: 33 kg.
Machine Dimention Machine Body: 1300mm x 880mm x 1300mm
Recovery Rate: 85%
C. Operating steps:
1. After opening the crate, plug in 220 V power, and connect the ground (earth).
2. Open the lid and fill the tank up to the level with solvent to be recovered (80 L)
3. Close the lid and tighten it.
4. Check all the pipe / hose make sure it is well connected. Especially vacuum pipe (6) and fresh come-out pipe (1).
5. Set up the thermostat(18) for example for Perc.is 150 degree C, for green chemical is 160-210 degree C. Vacuum tank pressure(3) high at 0.03 Mpa / low at 6.01Mpa, and steam cooling fan thermostat(11) at 40 degree C.
6. Turn on the power switch (15), steam cooling switch (16), heater switch (17) and vacuum pump switch (12).
7. If you want to be controlled with timer, it depends on the quantity of the chemical, set up the timer (14) then turn on the switch (13).
D. Important:
1. Install the unit in a wide and ventilated place.
2. Disconnect electric power before doing any action.
3. No taking off the control panel
4. Change the diathermic oil every 1000 working hours.
5. No filling the solvent container up over the level (80 liters)
6. Remove the waste after every recovery process
· : 30 ltr
SpecificationsB. Technical information:
Recovery volume : 200 liters
Power consume: 380V 10KW
Diathermic oil : 80 KG
Machine dimention: 2500x1700x2300 mm
Recovery Rate: 85%
Additional Information:
Approx. Rs 9.5 Lakh / UnitGet Latest Price
Product Details:Minimum Order Quantity | 1 Unit |
Capacity | 100 |
Design Type | Standard |
Brand/Make | Innovative FlexoTech Pvt.Ltd. |
@flexo 30L - RHB / @flexo 60L-RHB / @flexo 80L-RHB / @flexo 100L-RHB / @flexo 200L-RHB
Special Features Solvent recovery unit for photopolymer flexo plates
A. General description:
This is designed for recovery of flexographic photopolymer plate solvent washout chemical and any environmental green chemical with specialties of distilling and cooling, can be connected with in-line processor and any plate washout machine directly. With cold air circulation and drain out of residue for high speed recovery. Super recovering rate in the shortest time, is an ideal and high efficient recovery unit for flexographer.
B. Technical information:
Recovery volume : 200 liters
Power consume: 380V 10KW
Diathermic oil : 23 KG
Machine dimension: Main body: 2500x 1700x 2300 mm
Recovery rate: 85%
Recovery time : 6 ~ 7 hours
C. Operating steps:
1. After opening the crate, plug in 220 V power, and connect the ground (earth).
2. Open the lid and fill the tank up to the level with solvent to be recovered (80 L)
3. Close the lid and tighten it.
4. Check all the pipe / hose make sure it is well connected. Especially vacuum pipe (6) and fresh come-out pipe(1).
5. Set up the thermostat(18) for example for Perc.is 150 degree C, for green chemical is 160-210 degree C. Vacuum tank pressure(3) high at 0.03 Mpa / low at 6.01Mpa, and steam cooling fan thermostat(11) at 40 degree C.
6. Turn on the power switch(15), steam cooling switch(16), heater switch(17) and vacuum pump switch(12).
7. If you want to be controlled with timer, it depends on the quantity of the chemical, set up the timer(14) then turn on the switch(13).
D. Important:
1. Install the unit in a wide and ventilated place.
2. Disconnect electric power before doing any action.
3. No taking off the control panel
4. Change the diathermic oil every 1000 working hours.
5. No filling the solvent container up over the level (80 liters)
6. Remove the waste after every recovery process
Additional Information:
Approx. Rs 4.5 Lakh / UnitGet Latest Price
Product Details:Minimum Order Quantity | 1 Unit |
Brand/Make | Innovative FlexoTech Pvt.Ltd. |
Design Type | Standard |
Installation Services Yes
Additional Information:
Approx. Rs 4.5 Lakh / UnitGet Latest Price
Product Details:Minimum Order Quantity | 1 Unit |
Brand/Make | Innovative FlexoTech Pvt.Ltd. |
Design Type | Standard |
Additional Information:
Approx. Rs 4.5 Lakh / UnitGet Latest Price
Product Details:Minimum Order Quantity | 1 Unit |
Design Type | Standard |
Brand/Make | Innovative FlexoTech Pvt.Ltd. |
Capacity | 100 |
Additional Information:
Approx. Rs 3.45 Lakh / UnitGet Latest Price
Product BrochureProduct Details:Minimum Order Quantity | 1 Unit |
Design Type | Standard |
Brand/Make | Innovative FlexoTech Pvt.Ltd. |
Special Features:Solvent recovery unit for photopolymer flexo plates
A. General description:
This is designed for recovery of flexographic photopolymer plate solvent washout chemical and any environmental green chemical with specialties of distilling and cooling can be connected with in-line processor and any plate washout machine directly. With cold air circulation and drain out of residue for high speed recovery. Super recovering rate in the shortest time, is an ideal and high efficient recovery unit for flexographer.
B. Technical information:
Recovery Volume: 80 Liter
Power Consume: 220v AC, 5.65Kw
Dia Thermic Oil: 33 kg.
Machine Dimention Machine Boady: 1300mm x 880mm x 1300mm
Recovery Rate: 85%
C. Operating steps:
1. After opening the crate, plug in 220 V power, and connect the ground (earth).
2. Open the lid and fill the tank up to the level with solvent to be recovered (80 L)
3. Close the lid and tighten it.
4. Check all the pipe / hose make sure it is well connected. Especially vacuum pipe (6) and fresh come-out pipe (1).
5. Set up the thermostat(18) for example for Perc.is 150 degree C, for green chemical is 160-210 degree C. Vacuum tank pressure(3) high at 0.03 Mpa / low at 6.01Mpa, and steam cooling fan thermostat(11) at 40 degree C.
6. Turn on the power switch (15), steam cooling switch (16), heater switch (17) and vacuum pump switch (12).
7. If you want to be controlled with timer, it depends on the quantity of the chemical, set up the timer (14) then turn on the switch (13).
D. Important:
1. Install the unit in a wide and ventilated place.
2. Disconnect electric power before doing any action.
3. No taking off the control panel
4. Change the diathermic oil every 1000 working hours.
5. No filling the solvent container up over the level (80 liters)
6. Remove the waste after every recovery process
· : 30 ltr
SpecificationsB. Technical information:
Recovery volume : 30 liters
Power consume: 220V 3.65KW
Diathermic oil : 20 KG
Machine dimention: 960x610x940
Additional Information:
Approx. Rs 3.5 Lakh / UnitGet Latest Price
Product Details:Minimum Order Quantity | 1 Unit |
Automatic Grade | Automatic |
Design Type | Standard |
Special Features:Solvent recovery unit for photopolymer flexo plates
A. General description:
This is designed for recovery of flexographic photopolymer plate solvent washout chemical and any environmental green chemical with specialties of distilling and cooling can be connected with in-line processor and any plate washout machine directly. With cold air circulation and drain out of residue for high speed recovery. Super recovering rate in the shortest time, is an ideal and high efficient recovery unit for flexographer.
B. Technical information:
Recovery Volume: 80 Liter
Power Consume: 220v AC, 5.65Kw
Dia Thermic Oil: 33 kg.
Machine Dimention Machine Boady: 1300mm x 880mm x 1300mm
Recovery Rate: 85%
C. Operating steps:
1. After opening the crate, plug in 220 V power, and connect the ground (earth).
2. Open the lid and fill the tank up to the level with solvent to be recovered (80 L)
3. Close the lid and tighten it.
4. Check all the pipe / hose make sure it is well connected. Especially vacuum pipe (6) and fresh come-out pipe (1).
5. Set up the thermostat(18) for example for Perc.is 150 degree C, for green chemical is 160-210 degree C. Vacuum tank pressure(3) high at 0.03 Mpa / low at 6.01Mpa, and steam cooling fan thermostat(11) at 40 degree C.
6. Turn on the power switch (15), steam cooling switch (16), heater switch (17) and vacuum pump switch (12).
7. If you want to be controlled with timer, it depends on the quantity of the chemical, set up the timer (14) then turn on the switch (13).
D. Important:
1. Install the unit in a wide and ventilated place.
2. Disconnect electric power before doing any action.
3. No taking off the control panel
4. Change the diathermic oil every 1000 working hours.
5. No filling the solvent container up over the level (80 liters)
6. Remove the waste after every recovery process
· : 30 ltr
SpecificationsB. Technical information:
Recovery volume : 60 liters
Power consume: 220V 4.65KW
Diathermic oil : 23 KG
Machine dimention: 1100x780x1200 mm
Additional Information:
Approx. Rs 5.6 Lakh / UnitGet Latest Price
Product BrochureProduct Details:Minimum Order Quantity | 1 Unit |
Design Type | Standard |
Automatic Grade | Automatic |
Special Features: Solvent recovery unit for photopolymer flexo plates
A. General description:
This is designed for recovery of flexographic photopolymer plate solvent washout chemical and any environmental green chemical with specialties of distilling and cooling can be connected with in-line processor and any plate washout machine directly. With cold air circulation and drain out of residue for high speed recovery. Super recovering rate in the shortest time, is an ideal and high efficient recovery unit for flexographer.
B. Technical information:
Recovery Volume: 80 Liter
Power Consume: 220v AC, 5.65Kw
Dia Thermic Oil: 33 kg.
Machine Dimention Machine Boady: 1300mm x 880mm x 1300mm
Recovery Rate: 85%
C. Operating steps:
1. After opening the crate, plug in 220 V power, and connect the ground (earth).
2. Open the lid and fill the tank up to the level with solvent to be recovered (80 L)
3. Close the lid and tighten it.
4. Check all the pipe / hose make sure it is well connected. Especially vacuum pipe (6) and fresh come-out pipe (1).
5. Set up the thermostat(18) for example for Perc.is 150 degree C, for green chemical is 160-210 degree C. Vacuum tank pressure(3) high at 0.03 Mpa / low at 6.01Mpa, and steam cooling fan thermostat(11) at 40 degree C.
6. Turn on the power switch (15), steam cooling switch (16), heater switch (17) and vacuum pump switch (12).
7. If you want to be controlled with timer, it depends on the quantity of the chemical, set up the timer (14) then turn on the switch (13).
D. Important:
1. Install the unit in a wide and ventilated place.
2. Disconnect electric power before doing any action.
3. No taking off the control panel
4. Change the diathermic oil every 1000 working hours.
5. No filling the solvent container up over the level (80 liters)
6. Remove the waste after every recovery process
Specifications
B. Technical information:
Recovery volume : 100 liters
Power consume: 220V 6.65KW
Diathermic oil : 40 KG
Machine dimention: 1500x980x1500 mm
Recovery Rate: 85%
Additional Information:
Approx. Rs 2.25 Lakh / UnitGet Latest Price
Product BrochureProduct Details:Minimum Order Quantity | 1 Unit |
Design Type | Standard |
@flexo 30L - RHB / @flexo 60L-RHB / @flexo 80L-RHB / @flexo 100L-RHB / @flexo 200L-RHB
Special Features Solvent recovery unit for photopolymer flexo plates
A. General description:
This is designed for recovery of flexographic photopolymer plate solvent washout chemical and any environmental green chemical with specialties of distilling and cooling, can be connected with in-line processor and any plate washout machine directly. With cold air circulation and drain out of residue for high speed recovery. Super recovering rate in the shortest time, is an ideal and high efficient recovery unit for flexographer.
B. Technical information:
Recovery volume : 30 liters
Power consume: 220V 3.65KW
Diathermic oil : 20 KG
Machine dimension: Main body: 960x 610x940 mm
Recovery rate: 85%
Recovery time : 3 ~ 4 hours
C. Operating steps:
1. After opening the crate, plug in 220 V power, and connect the ground (earth).
2. Open the lid and fill the tank up to the level with solvent to be recovered (80 L)
3. Close the lid and tighten it.
4. Check all the pipe / hose make sure it is well connected. Especially vacuum pipe (6) and fresh come-out pipe(1).
5. Set up the thermostat(18) for example for Perc.is 150 degree C, for green chemical is 160-210 degree C. Vacuum tank pressure(3) high at 0.03 Mpa / low at 6.01Mpa, and steam cooling fan thermostat(11) at 40 degree C.
6. Turn on the power switch(15), steam cooling switch(16), heater switch(17) and vacuum pump switch(12).
7. If you want to be controlled with timer, it depends on the quantity of the chemical, set up the timer(14) then turn on the switch(13).
D. Important:
1. Install the unit in a wide and ventilated place.
2. Disconnect electric power before doing any action.
3. No taking off the control panel
4. Change the diathermic oil every 1000 working hours.
5. No filling the solvent container up over the level (80 liters)
6. Remove the waste after every recovery process
Additional Information:
Approx. Rs 6.5 Lakh / UnitGet Latest Price
Product BrochureProduct Details:Minimum Order Quantity | 1 Unit |
Brand/Make | Innovative FlexoTech Pvt.Ltd. |
Design Type | Standard |
@flexo 30L - RHB / @flexo 60L-RHB / @flexo 80L-RHB / @flexo 100L-RHB / @flexo 200L-RHB
Special Features Solvent recovery unit for photopolymer flexo plates
A. General description:
This is designed for recovery of flexographic photopolymer plate solvent washout chemical and any environmental green chemical with specialties of distilling and cooling, can be connected with in-line processor and any plate washout machine directly. With cold air circulation and drain out of residue for high speed recovery. Super recovering rate in the shortest time, is an ideal and high efficient recovery unit for flexographer.
B. Technical information:
Recovery volume : 60 / 80 liters
Power consume: 220V 4.65KW
Diathermic oil : 23 KG
Machine dimension: Main body: 1100x 780x1200 mm
Recovery rate: 85%
Recovery time : 3 ~ 4 hours
C. Operating steps:
1. After opening the crate, plug in 220 V power, and connect the ground (earth).
2. Open the lid and fill the tank up to the level with solvent to be recovered (80 L)
3. Close the lid and tighten it.
4. Check all the pipe / hose make sure it is well connected. Especially vacuum pipe (6) and fresh come-out pipe(1).
5. Set up the thermostat(18) for example for Perc.is 150 degree C, for green chemical is 160-210 degree C. Vacuum tank pressure(3) high at 0.03 Mpa / low at 6.01Mpa, and steam cooling fan thermostat(11) at 40 degree C.
6. Turn on the power switch(15), steam cooling switch(16), heater switch(17) and vacuum pump switch(12).
7. If you want to be controlled with timer, it depends on the quantity of the chemical, set up the timer(14) then turn on the switch(13).
D. Important:
1. Install the unit in a wide and ventilated place.
2. Disconnect electric power before doing any action.
3. No taking off the control panel
4. Change the diathermic oil every 1000 working hours.
5. No filling the solvent container up over the level (80 liters)
6. Remove the waste after every recovery process
Additional Information:
Approx. Rs 4.5 Lakh / UnitGet Latest Price
Product BrochureProduct Details:Brand/Make | Innovative Flexotech Pvt.Ltd. |
Design Type | Standard |
Special Features:Solvent recovery unit for photopolymer flexo plates
A. General description:
This is designed for recovery of flexographic photopolymer plate solvent washout chemical and any environmental green chemical with specialties of distilling and cooling can be connected with in-line processor and any plate washout machine directly. With cold air circulation and drain out of residue for high speed recovery. Super recovering rate in the shortest time, is an ideal and high efficient recovery unit for flexographer.
B. Technical information:
Recovery Volume: 80 Liter
Power Consume: 220v AC, 5.65Kw
Dia Thermic Oil: 33 kg.
Machine Dimention Machine Body: 1300mm x 880mm x 1300mm
Recovery Rate: 85%
C. Operating steps:
1. After opening the crate, plug in 220 V power, and connect the ground (earth).
2. Open the lid and fill the tank up to the level with solvent to be recovered (80 L)
3. Close the lid and tighten it.
4. Check all the pipe / hose make sure it is well connected. Especially vacuum pipe (6) and fresh come-out pipe (1).
5. Set up the thermostat(18) for example for Perc.is 150 degree C, for green chemical is 160-210 degree C. Vacuum tank pressure(3) high at 0.03 Mpa / low at 6.01Mpa, and steam cooling fan thermostat(11) at 40 degree C.
6. Turn on the power switch (15), steam cooling switch (16), heater switch (17) and vacuum pump switch (12).
7. If you want to be controlled with timer, it depends on the quantity of the chemical, set up the timer (14) then turn on the switch (13).
D. Important:
1. Install the unit in a wide and ventilated place.
2. Disconnect electric power before doing any action.
3. No taking off the control panel
4. Change the diathermic oil every 1000 working hours.
5. No filling the solvent container up over the level (80 liters)
6. Remove the waste after every recovery process
· : 30 ltr
SpecificationsB. Technical information:
Recovery volume : 60 / 80 liters
Power consume: 220V 4.65KW
Diathermic oil : 23 KG
Machine dimension
Additional Information:
Approx. Rs 5.4 Lakh / UnitGet Latest Price
Product Details:Brand/Make | Innovative Flexotech Pvt.Ltd. |
Design Type | Standard |
Special Features:Solvent recovery unit for photopolymer flexo plates
A. General description:
This is designed for recovery of flexographic photopolymer plate solvent washout chemical and any environmental green chemical with specialties of distilling and cooling can be connected with in-line processor and any plate washout machine directly. With cold air circulation and drain out of residue for high speed recovery. Super recovering rate in the shortest time, is an ideal and high efficient recovery unit for flexographer.
B. Technical information:
Recovery Volume: 80 Liter
Power Consume: 220v AC, 5.65Kw
Dia Thermic Oil: 33 kg.
Machine Dimention Machine Boady: 1300mm x 880mm x 1300mm
Recovery Rate: 85%
C. Operating steps:
1. After opening the crate, plug in 220 V power, and connect the ground (earth).
2. Open the lid and fill the tank up to the level with solvent to be recovered (80 L)
3. Close the lid and tighten it.
4. Check all the pipe / hose make sure it is well connected. Especially vacuum pipe (6) and fresh come-out pipe (1).
5. Set up the thermostat(18) for example for Perc.is 150 degree C, for green chemical is 160-210 degree C. Vacuum tank pressure(3) high at 0.03 Mpa / low at 6.01Mpa, and steam cooling fan thermostat(11) at 40 degree C.
6. Turn on the power switch (15), steam cooling switch (16), heater switch (17) and vacuum pump switch (12).
7. If you want to be controlled with timer, it depends on the quantity of the chemical, set up the timer (14) then turn on the switch (13).
D. Important:
1. Install the unit in a wide and ventilated place.
2. Disconnect electric power before doing any action.
3. No taking off the control panel
4. Change the diathermic oil every 1000 working hours.
5. No filling the solvent container up over the level (80 liters)
6. Remove the waste after every recovery process
· : 30 ltr
SpecificationsB. Technical information:
Recovery volume : 60 / 80 liters
Power consume: 220V 4.65KW
Diathermic oil : 23 KG
Machine dimen
Additional Information:
Approx. Rs 8.5 Lakh / UnitGet Latest Price
Product BrochureProduct Details:Minimum Order Quantity | 1 Unit |
Design Type | Standard |
Brand/Make | Innovative FlexoTech Pvt.Ltd. |
Special Features:Solvent recovery unit for photopolymer flexo plates
A. General description:
This is designed for recovery of flexographic photopolymer plate solvent washout chemical and any environmental green chemical with specialties of distilling and cooling can be connected with in-line processor and any plate washout machine directly. With cold air circulation and drain out of residue for high speed recovery. Super recovering rate in the shortest time, is an ideal and high efficient recovery unit for flexographer.
B. Technical information:
Recovery Volume: 80 Liter
Power Consume: 220v AC, 5.65Kw
Dia Thermic Oil: 33 kg.
Machine Dimention Machine Boady: 1300mm x 880mm x 1300mm
Recovery Rate: 85%
C. Operating steps:
1. After opening the crate, plug in 220 V power, and connect the ground (earth).
2. Open the lid and fill the tank up to the level with solvent to be recovered (80 L)
3. Close the lid and tighten it.
4. Check all the pipe / hose make sure it is well connected. Especially vacuum pipe (6) and fresh come-out pipe (1).
5. Set up the thermostat(18) for example for Perc.is 150 degree C, for green chemical is 160-210 degree C. Vacuum tank pressure(3) high at 0.03 Mpa / low at 6.01Mpa, and steam cooling fan thermostat(11) at 40 degree C.
6. Turn on the power switch (15), steam cooling switch (16), heater switch (17) and vacuum pump switch (12).
7. If you want to be controlled with timer, it depends on the quantity of the chemical, set up the timer (14) then turn on the switch (13).
D. Important:
1. Install the unit in a wide and ventilated place.
2. Disconnect electric power before doing any action.
3. No taking off the control panel
4. Change the diathermic oil every 1000 working hours.
5. No filling the solvent container up over the level (80 liters)
6. Remove the waste after every recovery process
· : 30 ltr
SpecificationsB. Technical information:
Recovery volume : 60 / 80 liters
Power consume: 220V 4.65KW
Diathermic oil : 23 KG
Additional Information:
Approx. Rs 9.5 Lakh / UnitGet Latest Price
Product BrochureProduct Details:Minimum Order Quantity | 1 Unit |
Design Type | Standard |
Brand/Make | Innovative FlexoTech Pvt.Ltd. |
@flexo 30L - RHB / @flexo 60L-RHB / @flexo 80L-RHB / @flexo 100L-RHB / @flexo 200L-RHB
Special Features Solvent recovery unit for photopolymer flexo plates
A. General description:
This is designed for recovery of flexographic photopolymer plate solvent washout chemical and any environmental green chemical with specialties of distilling and cooling, can be connected with in-line processor and any plate washout machine directly. With cold air circulation and drain out of residue for high speed recovery. Super recovering rate in the shortest time, is an ideal and high efficient recovery unit for flexographer.
B. Technical information:
Recovery volume : 60 / 80 liters
Power consume: 220V 4.65KW
Diathermic oil : 23 KG
Machine dimension: Main body: 1100x 780x1200 mm
Recovery rate: 85%
Recovery time : 3 ~ 4 hours
C. Operating steps:
1. After opening the crate, plug in 220 V power, and connect the ground (earth).
2. Open the lid and fill the tank up to the level with solvent to be recovered (80 L)
3. Close the lid and tighten it.
4. Check all the pipe / hose make sure it is well connected. Especially vacuum pipe (6) and fresh come-out pipe(1).
5. Set up the thermostat(18) for example for Perc.is 150 degree C, for green chemical is 160-210 degree C. Vacuum tank pressure(3) high at 0.03 Mpa / low at 6.01Mpa, and steam cooling fan thermostat(11) at 40 degree C.
6. Turn on the power switch(15), steam cooling switch(16), heater switch(17) and vacuum pump switch(12).
7. If you want to be controlled with timer, it depends on the quantity of the chemical, set up the timer(14) then turn on the switch(13).
D. Important:
1. Install the unit in a wide and ventilated place.
2. Disconnect electric power before doing any action.
3. No taking off the control panel
4. Change the diathermic oil every 1000 working hours.
5. No filling the solvent container up over the level (80 liters)
6. Remove the waste after every recovery process
Additional Information:
Approx. Rs 5.4 Lakh / UnitGet Latest Price
Product BrochureProduct Details:Minimum Order Quantity | 1 Unit |
Capacity | 100 |
Design Type | Standard |
Brand/Make | Innovative FlexoTech Pvt.Ltd. |
Special Features:Solvent recovery unit for photopolymer flexo plates
A. General description:
This is designed for recovery of flexographic photopolymer plate solvent washout chemical and any environmental green chemical with specialties of distilling and cooling can be connected with in-line processor and any plate washout machine directly. With cold air circulation and drain out of residue for high speed recovery. Super recovering rate in the shortest time, is an ideal and high efficient recovery unit for flexographer.
B. Technical information:
Recovery Volume: 80 Liter
Power Consume: 220v AC, 5.65Kw
Dia Thermic Oil: 33 kg.
Machine Dimention Machine Boady: 1300mm x 880mm x 1300mm
Recovery Rate: 85%
C. Operating steps:
1. After opening the crate, plug in 220 V power, and connect the ground (earth).
2. Open the lid and fill the tank up to the level with solvent to be recovered (80 L)
3. Close the lid and tighten it.
4. Check all the pipe / hose make sure it is well connected. Especially vacuum pipe (6) and fresh come-out pipe (1).
5. Set up the thermostat(18) for example for Perc.is 150 degree C, for green chemical is 160-210 degree C. Vacuum tank pressure(3) high at 0.03 Mpa / low at 6.01Mpa, and steam cooling fan thermostat(11) at 40 degree C.
6. Turn on the power switch (15), steam cooling switch (16), heater switch (17) and vacuum pump switch (12).
7. If you want to be controlled with timer, it depends on the quantity of the chemical, set up the timer (14) then turn on the switch (13).
D. Important:
1. Install the unit in a wide and ventilated place.
2. Disconnect electric power before doing any action.
3. No taking off the control panel
4. Change the diathermic oil every 1000 working hours.
5. No filling the solvent container up over the level (80 liters)
6. Remove the waste after every recovery process
· : 30 ltr
SpecificationsB. Technical information:
Recovery volume : 60 / 80 liters
Power consume: 220V 4.65KW
Diathermic oil : 23 KG
Machine dimension
Product Code:80 L
Additional Information:
Approx. Rs 5.6 Lakh / UnitGet Latest Price
Product Details:Minimum Order Quantity | 1 Unit |
Design Type | Standard |
Capacity | 100 |
Brand/Make | Innovative FlexoTech Pvt.Ltd. |
Special Features:Solvent recovery unit for photopolymer flexo plates
A. General description:
This is designed for recovery of flexographic photopolymer plate solvent washout chemical and any environmental green chemical with specialties of distilling and cooling can be connected with in-line processor and any plate washout machine directly. With cold air circulation and drain out of residue for high speed recovery. Super recovering rate in the shortest time, is an ideal and high efficient recovery unit for flexographer.
B. Technical information:
Recovery Volume: 80 Liter
Power Consume: 220v AC, 5.65Kw
Dia Thermic Oil: 33 kg.
Machine Dimention Machine Boady: 1300mm x 880mm x 1300mm
Recovery Rate: 85%
C. Operating steps:
1. After opening the crate, plug in 220 V power, and connect the ground (earth).
2. Open the lid and fill the tank up to the level with solvent to be recovered (80 L)
3. Close the lid and tighten it.
4. Check all the pipe / hose make sure it is well connected. Especially vacuum pipe (6) and fresh come-out pipe (1).
5. Set up the thermostat(18) for example for Perc.is 150 degree C, for green chemical is 160-210 degree C. Vacuum tank pressure(3) high at 0.03 Mpa / low at 6.01Mpa, and steam cooling fan thermostat(11) at 40 degree C.
6. Turn on the power switch (15), steam cooling switch (16), heater switch (17) and vacuum pump switch (12).
7. If you want to be controlled with timer, it depends on the quantity of the chemical, set up the timer (14) then turn on the switch (13).
D. Important:
1. Install the unit in a wide and ventilated place.
2. Disconnect electric power before doing any action.
3. No taking off the control panel
4. Change the diathermic oil every 1000 working hours.
5. No filling the solvent container up over the level (80 liters)
6. Remove the waste after every recovery process
Specifications
B. Technical information:
Recovery volume : 100 liters
Power consume: 220V 6.65KW
Diathermic oil : 40 KG
Machine dimension: Main body: 1500x 980x 1500 mm
Recovery rate: 85%
Recovery time : 6 ~ 7 hours
Additional Information:
Approx. Rs 11.5 Lakh / UnitGet Latest Price
Product BrochureProduct Details:Minimum Order Quantity | 1 Unit |
Design Type | Standard |
Brand/Make | Innovative FlexoTech Pvt.Ltd. |
@flexo 30L - RHB / @flexo 60L-RHB / @flexo 80L-RHB / @flexo 100L-RHB / @flexo 200L-RHB
Special Features Solvent recovery unit for photopolymer flexo plates
A. General description:
This is designed for recovery of flexographic photopolymer plate solvent washout chemical and any environmental green chemical with specialties of distilling and cooling, can be connected with in-line processor and any plate washout machine directly. With cold air circulation and drain out of residue for high speed recovery. Super recovering rate in the shortest time, is an ideal and high efficient recovery unit for flexographer.
B. Technical information:
Recovery volume : 60 / 80 liters
Power consume: 220V 4.65KW
Diathermic oil : 23 KG
Machine dimension: Main body: 1100x 780x1200 mm
Recovery rate: 85%
Recovery time : 3 ~ 4 hours
C. Operating steps:
1. After opening the crate, plug in 220 V power, and connect the ground (earth).
2. Open the lid and fill the tank up to the level with solvent to be recovered (80 L)
3. Close the lid and tighten it.
4. Check all the pipe / hose make sure it is well connected. Especially vacuum pipe (6) and fresh come-out pipe(1).
5. Set up the thermostat(18) for example for Perc.is 150 degree C, for green chemical is 160-210 degree C. Vacuum tank pressure(3) high at 0.03 Mpa / low at 6.01Mpa, and steam cooling fan thermostat(11) at 40 degree C.
6. Turn on the power switch(15), steam cooling switch(16), heater switch(17) and vacuum pump switch(12).
7. If you want to be controlled with timer, it depends on the quantity of the chemical, set up the timer(14) then turn on the switch(13).
D. Important:
1. Install the unit in a wide and ventilated place.
2. Disconnect electric power before doing any action.
3. No taking off the control panel
4. Change the diathermic oil every 1000 working hours.
5. No filling the solvent container up over the level (80 liters)
6. Remove the waste after every recovery process
Additional Information:
Approx. Rs 9.5 Lakh / UnitGet Latest Price
Product Details:Minimum Order Quantity | 1 Unit |
Design Type | Standard |
Brand/Make | Innovative FlexoTech Pvt.Ltd. |
Additional Information:
Approx. Rs 9.5 Lakh / UnitGet Latest Price
Product BrochureProduct Details:Minimum Order Quantity | 1 Unit |
Capacity | 100 |
Design Type | Standard |
Brand/Make | Innovative FlexoTech Pvt.Ltd. |
Additional Information:
Explore More Products
3.9/5
Rated by 40 Users
© Innovative Flexotech Private Limited. All Rights Reserved (Terms of Use)
Developed and Managed by IndiaMART InterMESH Limited