Solvent Recycling System

Approx. Rs 1.75 Lakh / UnitGet Latest Price

Product Details:

General Description:

• This is designed for recovery of flexographic photopolymer plate solvent washout chemical and any environmental green chemical with specialties of distilling and cooling, can be connected with in-line processor and any plate washout machine directly. With cold air circulation and drain out of residue for high speed recovery. Super recovering rate in the shortest time, is an ideal and high efficient recovery unit for flexographer.

Operating steps:

• After opening the crate, plug in 220 V power, and connect the ground (earth).
• Open the lid and fill the tank up to the level with solvent to be recovered (80 L)
• Close the lid and tighten it.
• Check all the pipe / hose make sure it is well connected. Especially vacuum pipe (6) and fresh come-out pipe(1).
• Set up the thermostat(18) for example for Perc.is 150 degree C, for green chemical is 160-210 degree C. Vacuum tank pressure(3) high at 0.03 Mpa / low at 6.01Mpa, and steam cooling fan thermostat(11) at 40 degree C.
• Turn on the power switch(15), steam cooling switch(16), heater switch(17) and vacuum pump switch(12).
• If you want to be controlled with timer, it depends on the quantity of the chemical, set up the timer(14) then turn on the switch(13).

Important:

• Install the unit in a wide and ventilated place.
• Disconnect electric power before doing any action.
• No taking off the control panel.
• Change the diathermic oil every 1000 working hours.
• No filling the solvent container up over the level (80 liters).
• Remove the waste after every recovery process.

Approx. Rs 1.95 Lakh / UnitGet Latest Price

Product Details:

General Description:

• This is designed for recovery of flexographic photopolymer plate solvent washout chemical and any environmental green chemical with specialties of distilling and cooling, can be connected with in-line processor and any plate washout machine directly. With cold air circulation and drain out of residue for high speed recovery. Super recovering rate in the shortest time, is an ideal and high efficient recovery unit for flexographer.

Operating steps:

• After opening the crate, plug in 220 V power, and connect the ground (earth).
• Open the lid and fill the tank up to the level with solvent to be recovered (80 L)
• Close the lid and tighten it.
• Check all the pipe / hose make sure it is well connected. Especially vacuum pipe (6) and fresh come-out pipe(1).
• Set up the thermostat(18) for example for Perc.is 150 degree C, for green chemical is 160-210 degree C. Vacuum tank pressure(3) high at 0.03 Mpa / low at 6.01Mpa, and steam cooling fan thermostat(11) at 40 degree C.
• Turn on the power switch(15), steam cooling switch(16), heater switch(17) and vacuum pump switch(12).
• If you want to be controlled with timer, it depends on the quantity of the chemical, set up the timer(14) then turn on the switch(13).

Important:

• Install the unit in a wide and ventilated place.
• Disconnect electric power before doing any action.
• No taking off the control panel
• Change the diathermic oil every 1000 working hours.
• No filling the solvent container up over the level (80 liters)
• Remove the waste after every recovery process.

Approx. Rs 1.95 Lakh / pieceGet Latest Price

Product Details:

General Description:

• This is designed for recovery of flexographic photopolymer plate solvent washout chemical and any environmental green chemical with specialties of distilling and cooling, can be connected with in-line processor and any plate washout machine directly. With cold air circulation and drain out of residue for high speed recovery. Super recovering rate in the shortest time, is an ideal and high efficient recovery unit for flexographer.

Operating steps:

• After opening the crate, plug in 220 V power, and connect the ground (earth).
• Open the lid and fill the tank up to the level with solvent to be recovered (80 L)
• Close the lid and tighten it.
• Check all the pipe / hose make sure it is well connected. Especially vacuum pipe (6) and fresh come-out pipe(1).
• Set up the thermostat(18) for example for Perc.is 150 degree C, for green chemical is 160-210 degree C. Vacuum tank pressure(3) high at 0.03 Mpa / low at 6.01Mpa, and steam cooling fan thermostat(11) at 40 degree C.
• Turn on the power switch(15), steam cooling switch(16), heater switch(17) and vacuum pump switch(12).
• If you want to be controlled with timer, it depends on the quantity of the chemical, set up the timer(14) then turn on the switch(13).

Important:

• Install the unit in a wide and ventilated place.
• Disconnect electric power before doing any action.
• No taking off the control panel
• Change the diathermic oil every 1000 working hours.
• No filling the solvent container up over the level (80 liters)
• Remove the waste after every recovery process.

Approx. Rs 6.45 Lakh / UnitGet Latest Price

Product Details:

General Description:

• This is designed for recovery of flexographic photopolymer plate solvent washout chemical and any environmental green chemical with specialties of distilling and cooling, can be connected with in-line processor and any plate washout machine directly. With cold air circulation and drain out of residue for high speed recovery. Super recovering rate in the shortest time, is an ideal and high efficient recovery unit for flexographer.

Operating steps:

• After opening the crate, plug in 220 V power, and connect the ground (earth).
• Open the lid and fill the tank up to the level with solvent to be recovered (80 L)
• Close the lid and tighten it.
• Check all the pipe / hose make sure it is well connected. Especially vacuum pipe (6) and fresh come-out pipe(1).
• Set up the thermostat(18) for example for Perc.is 150 degree C, for green chemical is 160-210 degree C. Vacuum tank pressure(3) high at 0.03 Mpa / low at 6.01Mpa, and steam cooling fan thermostat(11) at 40 degree C.
• Turn on the power switch(15), steam cooling switch(16), heater switch(17) and vacuum pump switch(12).
• If you want to be controlled with timer, it depends on the quantity of the chemical, set up the timer(14) then turn on the switch(13).

Important:

• Install the unit in a wide and ventilated place.
• Disconnect electric power before doing any action.
• No taking off the control panel
• Change the diathermic oil every 1000 working hours.
• No filling the solvent container up over the level (80 liters)
• Remove the waste after every recovery process.

Approx. Rs 1.95 Lakh / PieceGet Latest Price

Product Details:

General description:

• This is designed for recovery of flexographic photopolymer plate solvent washout chemical and any environmental green chemical with specialties of distilling and cooling, can be connected with in-line processor and any plate washout machine directly. With cold air circulation and drain out of residue for high speed recovery. Super recovering rate in the shortest time, is an ideal and high efficient recovery unit for flexographer.

Operating steps:

• After opening the crate, plug in 220 V power, and connect the ground (earth).
• Open the lid and fill the tank up to the level with solvent to be recovered (80 L)
• Close the lid and tighten it.
• Check all the pipe / hose make sure it is well connected. Especially vacuum pipe (6) and fresh come-out pipe(1).
• Set up the thermostat(18) for example for Perc.is 150 degree C, for green chemical is 160-210 degree C. Vacuum tank pressure(3) high at 0.03 Mpa / low at 6.01Mpa, and steam cooling fan thermostat(11) at 40 degree C.
• Turn on the power switch(15), steam cooling switch(16), heater switch(17) and vacuum pump switch(12).
• If you want to be controlled with timer, it depends on the quantity of the chemical, set up the timer(14) then turn on the switch(13).

Important:

• Install the unit in a wide and ventilated place.
• Disconnect electric power before doing any action.
• No taking off the control panel
• Change the diathermic oil every 1000 working hours.
• No filling the solvent container up over the level (80 liters)
• Remove the waste after every recovery process.

Approx. Rs 1.75 Lakh / pieceGet Latest Price

Product Details:

With the assistance of our deft team of professionals, we are able to introduce a broad array of 30 Liter Solvent Recovery System. It is one of the environment friendly systems available in the industry. The system finds wide application use in recycling dirty solvent whether used or waste solvent. In various industrial processes where organic or non-organic substances are used, such recovery system helps in cleaning and recycling solvent from the machines. In addition, the system provides perfect distribution to production line.

Features:

• 32 stages of control function
• Less in material consumption
• Low maintenance cost

Other Details:

• Install the unit in a wide and ventilated place.
• Disconnect electric power before doing any action.
• No taking off the control panel
• Change the diathermic oil every 1000 working hours.
• No filling the solvent container up over the level (80 liters)
• Remove the waste after every recovery process

Operating Steps:

• After opening the crate, plug in 220 V power, and connect the ground (earth).
• Open the lid and fill the tank up to the level with solvent to be recovered (80 L)
• Close the lid and tighten it.
• Check all the pipe / hose make sure it is well connected. Especially vacuum pipe (6) and fresh come-out pipe(1).
• Set up the thermostat(18) for example for Perc.is 150 degree C, for green chemical is 160-210 degree C. Vacuum tank pressure(3) high at 0.03 Mpa / low at 6.01Mpa, and steam cooling fan thermostat(11) at 40 degree C.
• Turn on the power switch(15), steam cooling switch(16), heater switch(17) and vacuum pump switch(12).
• If you want to be controlled with timer, it depends on the quantity of the chemical, set up the timer(14) then turn on the switch(13).

Approx. Rs 2.3 Lakh / UnitGet Latest Price

Product Details:

General Description:

• This is designed for recovery of flexographic photopolymer plate solvent washout chemical and any environmental green chemical with specialties of distilling and cooling can be connected with in-line processor and any plate washout machine directly. With cold air circulation and drain out of residue for high speed recovery. Super recovering rate in the shortest time, is an ideal and high efficient recovery unit for flexographer.

Operating steps:

• After opening the crate, plug in 220 V power, and connect the ground (earth).
• Open the lid and fill the tank up to the level with solvent to be recovered (80 L)
• Close the lid and tighten it.
• Check all the pipe / hose make sure it is well connected. Especially vacuum pipe (6) and fresh come-out pipe (1).
• Set up the thermostat(18) for example for Perc.is 150 degree C, for green chemical is 160-210 degree C. Vacuum tank pressure(3) high at 0.03 Mpa / low at 6.01Mpa, and steam cooling fan thermostat(11) at 40 degree C.
• Turn on the power switch (15), steam cooling switch (16), heater switch (17) and vacuum pump switch (12).
• If you want to be controlled with timer, it depends on the quantity of the chemical, set up the timer (14) then turn on the switch (13).

Important:

• Install the unit in a wide and ventilated place.
• Disconnect electric power before doing any action.
• No taking off the control panel
• Change the diathermic oil every 1000 working hours.
• No filling the solvent container up over the level (80 liters)
• Remove the waste after every recovery process.

Approx. Rs 2.3 Lakh / UnitGet Latest Price

Product Details:

General Description:

• This is designed for recovery of flexographic photopolymer plate solvent washout chemical and any environmental green chemical with specialties of distilling and cooling can be connected with in-line processor and any plate washout machine directly. With cold air circulation and drain out of residue for high speed recovery. Super recovering rate in the shortest time, is an ideal and high efficient recovery unit for flexographer.

Operating steps:

• After opening the crate, plug in 220 V power, and connect the ground (earth).
• Open the lid and fill the tank up to the level with solvent to be recovered (80 L)
• Close the lid and tighten it.
• Check all the pipe / hose make sure it is well connected. Especially vacuum pipe (6) and fresh come-out pipe (1).
• Set up the thermostat(18) for example for Perc.is 150 degree C, for green chemical is 160-210 degree C. Vacuum tank pressure(3) high at 0.03 Mpa / low at 6.01Mpa, and steam cooling fan thermostat(11) at 40 degree C.
• Turn on the power switch (15), steam cooling switch (16), heater switch (17) and vacuum pump switch (12).
• If you want to be controlled with timer, it depends on the quantity of the chemical, set up the timer (14) then turn on the switch (13).

Important:

• Install the unit in a wide and ventilated place.
• Disconnect electric power before doing any action.
• No taking off the control panel
• Change the diathermic oil every 1000 working hours.
• No filling the solvent container up over the level (80 liters)
• Remove the waste after every recovery process.

Approx. Rs 1.95 Lakh / UnitGet Latest Price

Product BrochureProduct Details:

General Description:

• This is designed for recovery of flexographic photopolymer plate solvent washout chemical and any environmental green chemical with specialties of distilling and cooling, can be connected with in-line processor and any plate washout machine directly. With cold air circulation and drain out of residue for high speed recovery. Super recovering rate in the shortest time, is an ideal and high efficient recovery unit for flexographer.

Operating steps:

• After opening the crate, plug in 220 V power, and connect the ground (earth).
• Open the lid and fill the tank up to the level with solvent to be recovered (80 L)
• Close the lid and tighten it.
• Check all the pipe / hose make sure it is well connected. Especially vacuum pipe (6) and fresh come-out pipe(1).
• Set up the thermostat(18) for example for Perc.is 150 degree C, for green chemical is 160-210 degree C. Vacuum tank pressure(3) high at 0.03 Mpa / low at 6.01Mpa, and steam cooling fan thermostat(11) at 40 degree C.
• Turn on the power switch(15), steam cooling switch(16), heater switch(17) and vacuum pump switch(12).
• If you want to be controlled with timer, it depends on the quantity of the chemical, set up the timer(14) then turn on the switch(13).

Important:

• Install the unit in a wide and ventilated place.
• Disconnect electric power before doing any action.
• No taking off the control panel
• Change the diathermic oil every 1000 working hours.
• No filling the solvent container up over the level (80 liters)
• Remove the waste after every recovery process.

Approx. Rs 6.45 Lakh / UnitGet Latest Price

Product BrochureProduct Details:

Since our inception, we are engaged in offering a wide range of excellent quality 200 Liter Solvent Distillation Unit. This machine helps in cleaning and distillation the chemical components and substances from the plate, rod and other equipment. It can clean entire types of solvent from the chemically dip solvents. Additionally, the control panel and one production line helps in increasing the product supply in a unit. Along with it, clients can get the unit from us at industry leading rates also within the stipulated period.

Features:

• High power consumption
• Easy stages for quick production
• Less noise

Other Details:

• Install the unit in a wide and ventilated place.
• Disconnect electric power before doing any action.
• No taking off the control panel
• Change the diathermic oil every 1000 working hours.
• No filling the solvent container up over the level (80 liters)
• Remove the waste after every recovery process

Operating Steps:

• After opening the crate, plug in 220 V power, and connect the ground (earth).
• Open the lid and fill the tank up to the level with solvent to be recovered (80 L)
• Close the lid and tighten it.
• Check all the pipe / hose make sure it is well connected. Especially vacuum pipe (6) and fresh come-out pipe(1).
• Set up the thermostat(18) for example for Perc.is 150 degree C, for green chemical is 160-210 degree C. Vacuum tank pressure(3) high at 0.03 Mpa / low at 6.01Mpa, and steam cooling fan thermostat(11) at 40 degree C.
• Turn on the power switch(15), steam cooling switch(16), heater switch(17) and vacuum pump switch(12).
• If you want to be controlled with timer, it depends on the quantity of the chemical, set up the timer(14) then turn on the switch(13).

Approx. Rs 1.95 Lakh / UnitGet Latest Price

Product Details:

General Description:

• This is designed for recovery of flexographic photopolymer plate solvent washout chemical and any environmental green chemical with specialties of distilling and cooling, can be connected with in-line processor and any plate washout machine directly. With cold air circulation and drain out of residue for high speed recovery. Super recovering rate in the shortest time, is an ideal and high efficient recovery unit for flexographer.

Operating steps:

• After opening the crate, plug in 220 V power, and connect the ground (earth).
• Open the lid and fill the tank up to the level with solvent to be recovered (80 L)
• Close the lid and tighten it.
• Check all the pipe / hose make sure it is well connected. Especially vacuum pipe (6) and fresh come-out pipe(1).
• Set up the thermostat(18) for example for Perc.is 150 degree C, for green chemical is 160-210 degree C. Vacuum tank pressure(3) high at 0.03 Mpa / low at 6.01Mpa, and steam cooling fan thermostat(11) at 40 degree C.
• Turn on the power switch(15), steam cooling switch(16), heater switch(17) and vacuum pump switch(12).
• If you want to be controlled with timer, it depends on the quantity of the chemical, set up the timer(14) then turn on the switch(13).

Important:

• Install the unit in a wide and ventilated place.
• Disconnect electric power before doing any action.
• No taking off the control panel
• Change the diathermic oil every 1000 working hours.
• No filling the solvent container up over the level (80 liters)
• Remove the waste after every recovery process.

Approx. Rs 2.5 Lakh / UnitGet Latest Price

Product Details:

Leveraging on our in-house production unit, we are offering a wide assortment of 60 Liter Thinner Recovery Equipment. This equipment can easily be used for recycling solvent according to the distillation principle. Furthermore, the equipment find wide application use in a variety of industries that use organic solvent as cleaning agent such as dirty solvent from cleaning the spray gun, trichloroethylene from cleaning electronic products, toluene, anhydrous alcohol, and IPA used as cleaning the optical lens. This machine is eco-friendly and do not contaminate the elements present in environment.

Features:

• High quality recycled solvent
• Clean and pure supply to the production line
• Durable and stable performance

Other Details:

• Install the unit in a wide and ventilated place.
• Disconnect electric power before doing any action.
• No taking off the control panel
• Change the diathermic oil every 1000 working hours.
• No filling the solvent container up over the level (80 liters)
• Remove the waste after every recovery process

Operating Steps:

• After opening the crate, plug in 220 V power, and connect the ground (earth).
• Open the lid and fill the tank up to the level with solvent to be recovered (80 L)
• Close the lid and tighten it.
• Check all the pipe / hose make sure it is well connected. Especially vacuum pipe (6) and fresh come-out pipe(1).
• Set up the thermostat(18) for example for Perc.is 150 degree C, for green chemical is 160-210 degree C. Vacuum tank pressure(3) high at 0.03 Mpa / low at 6.01Mpa, and steam cooling fan thermostat(11) at 40 degree C.
• Turn on the power switch(15), steam cooling switch(16), heater switch(17) and vacuum pump switch(12).If you want to be controlled with timer, it depends on the quantity of the chemical, set up the timer(14) then turn on the switch(13).